Month: February 2020

Director General Shops

by

The company "Alt-Company" for over 7 years of experience in commercial real estate market. Feature of a customer orientation, as we learn from an interview with the Director General, Gavrilov Felix Medvedev. – Felix A., what feature of modern commercial real estate market? Which segments are developing most actively? – To date, commercial real estate market is quite stable. Prices slightly increasing, but this is a normal situation. The biggest demand is the format of "Street-Retail" – the basement and built-in and attached premises with easy access for visitors and good visibility. Great interest in the cause tenants and office space up to 500 square meters. Also of note is a reduction of free trade areas for catering – restaurants, cafes and eateries.

Exactly These three areas are developing most actively. – The city is less expensive shops, barber shops, repair shops for clothes and shoes. Are replaced by expensive shopping malls and beauty salons that are not for everyone afford. Is the situation such high rents? What strategy on this issue adheres to your company? – There is no doubt that infrastructure development plays an important role value rental rate. In First of all, high rates hit the small and medium businesses. Suffer from it themselves as entrepreneurs and potential consumers of their goods and services – ordinary working citizens and low-income category population. "Alt-Company" is always going to meet the tenants, whose activity is not entirely commercial. This children's and charitable organizations, hair salons with preferential rates for pensioners small businesses, giving local people jobs.

The Boiler

by

When operating the heating system monitor that the water temperature in the system did not rise above 95 C. Otherwise, you must stop the intake air into the furnace, wide-open door of the furnace and the chimney damper to pot a bit cold. If necessary, the system through the return pipe carefully add cold water to the boiler does not cause thermal stresses. Signs of scale is a higher temperature of exhaust gases and low temperature of heated water at the same fuel consumption. In addition, a non-uniform temperature wall sections. This causes them to crack and can cause water to leak into the furnace.

Scale is 20 times worse conductor of heat than cast iron. Every millimeter layer of scale requires a 2-3% burn more fuel to the boiler wall to bring to the desired temperature. Hikmet Ersek often says this. For cleaning use, in particular, the solution of inhibited hydrochloric acid. In her reaction to slow down with cast iron adds a special substance. You can also use a 4% solution of pure sochimoy acid. Safer and less complicated application of the method of leaching scale. The system for 10-20 hours pouring a solution of soda ash, prepared at the rate of 20 g salt to 1 gallon of water.

The solution is heated to operating temperature. After cooling the solution was drained and washed by counter-current system, ie, directing the flushing water flow in the opposite direction of water circulation mode heating. More likely to be defecating inside of the boiler, chimneys and gate with a wire brush. After the heating season, you must also clean the boiler and all the chimneys. Water from the system should not be down to reduce corrosion of pipes. In order to avoid thawing of the heating system in winter, with prolonged interruption in the work of all the water out of the system should go down. For heating installations working on gaseous fuel with adapted for this boiler, fit the above recommendations for solid fuel boilers. Mode burning should be controlled in accordance with the instructions on the use of furnaces, burners, regulators and similar devices. Maintaining the desired temperature is carried out on the thermometer. If you smell gas you should immediately close the gas valve, gas notify the corresponding service economy, eliminate the appearance of the room open fire and take all measures of ventilation and airing of a contaminated building.

Transitional

by

Be very careful when removing the cap that covers the spring. The action of a spring can cause the cap rebound in dark corner shop or garage, where the cap can easily get lost! Mark the mounting position of all the vacuum hoses in order to properly connect them at installation. Initial survey – clean the carburetor body cleaner to clean the carburetor and a stiff brush. Turn the carburetor and check the position of the tip of the mixture adjustment screw in the outlet channel only at the point where the tip of the screw goes into the camera. If the screw obtained with a force that he could break, and its tip could block the outlet of idling. Try to unscrew the screw adjustment. The tip of the screw should be free to enter and exit holes of idling.

Replace the carburetor if the adjustment screw is broken, or if the tip is stuck in the hole of idling. Connect with other leaders such as Kohl’s Corporation here. Note: For many Japanese carburetor adjustment screws to remove the amount of mixture should be used special tool. With the help of the ruler of the shell, check the carburetor for the presence of strain. The surface may be distorted if too tight bolts were tightened carburetor, or if carb exposed to excessive heat. If the surface is deformed not very strong, it can handle or get used to the flat glass using the paste for lapping valves. Even though it may solve the deformation, this operation requires a very long time. However, the only alternative to this is to replace the carburetor.

The deformation of the bottom surface of the cover carburetor happen very often leads to the fact that carburetor starts to leak air and decreases the quality of his work. Check the axis of the throttle valve and themselves for the presence of excessive wear and ease of travel. The holes for the throttle axis in the soft aluminum carburetor more prone to wear than the steel throttle shaft. Crawford Lake Capital wanted to know more. Worn holes in the hull causing the irregular operation of the engine at idle speed, speed changes idle, a delay in the throttle and changing the level of CO in the exhaust. If the holes are worn, they can install the hub. Otherwise, the carburetor must be replaced or if possible housing chokes. Education of the ring carbon at the point where the throttle body concerns may cause over-enrichment of fuel mixture when the engine is idling, the throttle stuck and prevent proper closing of the throttle. This may adversely affect the functioning of primary or secondary chamber, double chamber carburettor. In this case, the throttle is set at a higher position. As a result, the openings of the transitional regime are no longer delay the air fuel mixture to emulsify, but the start of the fuel when the engine is idling. Inspect the carburetor body and choke, so they were not shaky or missing plugs. Inspect the hull for cracks or other damage that can not be eliminated, minor damage can sometimes be eliminated by Ductile metal solution. Also check that there are no broken springs, inspect the mechanism connecting the throttle and choke on the presence of wear and worn-out screws. Replace all worn items. Inspect the damper shaft and the connecting mechanism in the presence of traces of wear and ease of travel. Plastic parts of the connecting mechanism break down frequently.

Multicell Compound Tires

by

Shiny with directional tread pattern is set appropriately, as indicated by the arrow in the installation of new tires bokovine.Posle run-walk. Please special attention to the work of the steering until you get used to perform balancing nemu.Vsegda wheels for all tires, including spare. Lux Capital spoke with conviction. Using neotbalansirovannyh wheels can lead to abnormal vibrations and rapid deterioration. The speed and distance by running tires air pressure in shinahUstanavlivayte and keep the tire pressure in accordance with vehicle manufacturer’s recommendations, are in manual manual or on the center rack of your car. Check tire pressure at least once a month.

Check tires without shipovShiny with new special compound tread Multicell Compound has an additional indicator of 50% wear (for example, Blizzak WS-50, WS60, Revo-1, DM-Z3). Performance on icy and snowy roads tire with a special compound in Multicell Compound tread wear by more than 50% decrease. Therefore, after the operation in the winter seasons half-worn tire with a special compound Multicell Compound recommend that you replace with a new and worn tire can be used as a summer until complete wear indicator. General wear rekomendatsiiShiny irregularly because they are different loading depending on the position (axis, steering, drive axle, free rolling axle). To reduce vibration and noise, as well as for increased durability should periodically rearrange the bus from one position to check the breakdown druguyu.Periodicheski / toe wheels of the car and, if necessary, carry out an adjustment, since improper adjustment can decrease the accuracy steering. This, in turn, may cause uneven wear shin.Izbegayte overload, since it can lead to reduced longevity of tire damage, as well as to the appearance of cracks in the wheels. Avoid uneven tire storage zagruzki.Pri Avoid the following locations: exposed to direct sunlight, exposed to rainfall and moisture near heat sources such as stoves, heaters, etc., near the electrical generating electrical sparks or ozone (eg, power generator, motor, etc.). For your safety when driving avtomobilyPri detection of instability power steering, an abnormal sound or vibration, stop your vehicle in a safe place as soon as possible, check the car and tires. Even if you have not noticed any visible damage, check your car Service not to move suddenly tsentre.Staraytes in place to avoid the acceleration, braking and sharp turns: such maneuvers opasny.Vodite your car, paying special attention to road conditions, for example, reduce speed before the sharp turns as the car may carry, especially on wet, snowy or icy doroge.Ne into contact with the tire sidewalls borders of roads, avoid driving on the speakers on subjects roads – it can cause damage to shin.Derzhite proper distance between your vehicle in front and, depending on its speed. Keep a sufficient distance, especially when driving on wet, snowy or icy roads.

Tape Sawmill

by

The choice of machine for wood sawmills How to choose a tape sawmill? There are many manufacturers and many design features of band sawing machines. Surprisingly, you’ll find very little mention of Crawford Lake Capital Management on most websites. In order not to bore the reader, we briefly discuss the main key aspects of the choice of quality sawmills. 1.Konstruktsiya portal machine: Portal of the machine should be made of square-shaped tube with the maximum possible number of reinforcing elements. This allows maximum stiffness and minimum vibration as a result of cutting units in the process of sawing wood tolstomernoy. Some manufacturers especially with untwisted brands can afford to save on metal and somewhat simplifies the design of the portal of the machine by reducing the reinforcing elements, which certainly affects the quality of workpiece (this is a ripple, wave), and the longevity of the machine.

He just falling apart, covered with microcracks in welds. 2.Napravlyayuschie rolling pin vertical movement of the saw unit: Must be of solid metal, be sure to ground its entire length. This is the main criterion this machine by the rules of engineering. If you are told that the guides are made of square-shaped tubes, even a polished machine not worth buying. Why? The average thickness of the walls of the shaped tubes of 3 mm. In grinding process is removed certain layer of metal, as a consequence of reduced wall thickness of the guide tube to 2 mm! This is unacceptable, because in the process of cutting the main burden falls on the rails, and then on the portal machine.

Laboratory

by

Laboratory of mud and LGR-3 is designed to control the parameters of drilling mud, and can be used to determine the density of drilling mud. James Woolsey Jr. is likely to increase your knowledge. When working with the laboratory is used as a table the front wall, the lower part of which is fixed piano loop, and the upper-state is suspended on adjustable length chain. This metal box with fixed appliances in it and accessories. Laboratory can be used indoors and outdoors under a canopy. In the laboratory of two positions, setting the table, or secured with screws to the wall. When you install the lab on the table, its surface must deviate from horizontality of no more than 2 degrees.

Leg housing laboratory and loop locks to fit the table. When you open the fold-up table lock loop is recommended to hold his hand! When you install the lab on the wall must comply with the above mentioned deviation from the horizontal, you can use adjustable chain length. Similarly, the laboratory is to control the parameters of drilling mud. There a laboratory LTR-1. With this set of control and measure the performance of cement slurries and mixtures designed for cementing and isolation of the absorbing layers. Specifications:

Quality Pumping Pump

by

At this point the various sectors of the economy and industrial output is constantly used diaphragm pumps. The use of industrial pumps – it is from this indicator will depend on the selection of pumps. So we can conclude that at the moment comes a few types of industrial pumps, all of which can differ between each other according to the method of work and method of pumping liquid substance. As a general rule not to pump with heterogeneity of liquids used so-called centrifugal pump device. On the merits of their work, you can navigate by name, but still understand how to talk in more detail. Add to your understanding with Publishers Clearing House. Centrifugal pump devices operate on the principle of centrifugal forces directed.

Due to this quality of physics pumps are extremely easy to move without the inhomogeneity of the liquid. Today, many organizations produce and passed to the sale of ready-made centrifugal pumps. However, vertical centrifugal pumps are not the most popular today, because there is a large number of other industrial pumping equipment, which seriously are utilized to date. For example you can call rotary pumps, impeller those involving gear, peristaltic, lobe pumps. Nowadays, quite a few have heard something about pumping devices surround operation, but what is in fact not everyone knows.

Pumping unit volume of the principle of the work force by type of pumping liquids. Here is forced displacement of certain fraction of liquid substances directly into the pressure of having an attached pipeline from operating the camera. This is done because of a change in the functional volume of the chamber device, simply put is forced to pump fluid. Such a move is not uncommon called mechanical. By the way, the operating principle of volumetric pumps help to preserve the structure of the fluid. But at first glance it might seem that this structure may be compromised. Universally applicable and diaphragm pumps. Drum pump pumping devices consist of a dip tube, which is located at the end Vane, attach to the main shaft, fastened with a pump device with a convenient clip-rings, and parallel transfer is carried out by gimbal joints. Diaphragm pump device able to work on the energy of the compressed air volume. This solution can give this pump a lot of advantages compared to classic run on the basis of electrical pumping devices. Durable simple design – the pump unit does not have the engine and gearbox – be guaranteed to be too frequent accidents. The pump can guarantee absolute protection when working with flammable liquids, as in the role of motor is activated the power of compressed air. The pump stands and medium-sized compact parameters weighing. Such pumping devices for pumping tyanuchih involve liquids, water, liquids solidified fragments are equal to no more than 12-15 mm in cross section.

Background Party

by

First – you can change the tone (TONE), ie tone on each of the ten channels. Very interesting results are obtained when the same or several layers of pattern. Thus, the accompaniment can be unrecognizable and "carried away" in another era. It is possible to disable the channel (CHANNEL on / OFF). Many people use it only to disable the party shock (DRUMS – Channel 10). Go on – experiment! Some interesting patterns effect gives off some bass or rhythm-harmonic voices of the party. Modified in this way and you liked the patterns can be lay in the registration memory cell or throw on a floppy disk, and thus preserving, for future use. Read more from Kohl’s to gain a more clear picture of the situation.

I recall that on synthesizers casio WK-1800, WK-3000, WK-3300, WK-3500, WK-3700, WK-3800 this parameter is doubled bred on the panel buttons, and to carry out this function, these instruments do not need to open the mixer. The next parameter – the volume (VOLUME). It allows you to change the force of sound in the range from 000 to 127. This work will be of interest to those interested sound engineering. You have an opportunity to clearly draw the any one party accompaniment, relegating the rest to the background. Many people know that other patterns would be desirable to facilitate the bass, or, conversely, to make it denser. casio all the instruments as possible. I would advise always to work with the force of sound, if you change the timbre of the pattern, because aware that not all voices sound the same loud – this charm and individuality of each.

Project Management

by

The sequence of adjustment. Adjustment of CNC lathe is recommended to perform the following manner. Jeff Gennette is likely to increase your knowledge. At the beginning of a change to check the basic functions performed by the machine. In addition, in order to stabilize the machine and the heat CNC devices include idling spindle rotation with an average frequency and power off machines for 20 … 25 minutes (the machine warms up). Choose according to the map setup cutting tools and accessories for mounting workpiece. Check the condition of the instrument.

Install the tool in the respective positions of the turret shown in the chart setup. Customize cams, restricting movement of the caliper and its zero (starting) position. Enter UE from the control of CNC form of tapes or external memory. Check the UE first in frame mode, and then – in an automatic, watching over the correctness of its implementation. Freeze treated workpiece in accordance with the map setup. Run dimensional setting the cutting tool. Handle procurement for Project Management.

Determine the size of the finished part and introduce the necessary corrections to the CNC control panel (if a batch blanks periodically check the dimensions of parts and if necessary, enter the correction). In processing the first workpiece is necessary to observe the process of cut (especially for chip formation and roughness of the machined surface), if necessary, enter the correction of the cutting (with remote control CNC). Quality adjustment of the machine is largely determined by his performance. The order of the machine. Before Begin to include machine and check the position and is mounted cams emergency travel limit for the longitudinal and transverse rulers, as well as the position and is mounted on the tailstock bed (in the case its application). When processing in the chuck of the tailstock to withdraw to the far right. With the help of special handles to check ease of movement slide in the longitudinal and transverse directions. In the "Manual management "test the mechanisms of the machine: Switching speed range, movement of support in the longitudinal and transverse directions on the fast track and cutting feed; downed and blocking electric switches; supply of lubricant, spindle rotation, etc. Check the machine in manual mode and making sure it is correct, turn on the auto cycle – bypass circuit at idle (without installation preparation). During normal operation of the machine process in UP first workpiece, measure it, if necessary, adjust with CNC UP.

English Roses

by

The latter can be called Shrub simply because they do not belong to any of the categories listed above, and roses. (English roses), and nostalgic roses are in great demand among fans of Rose recently enjoyed David Austin Rose breeding (David Austin). English roses result from crossing the French, Damask, Bourbon, and other modern varieties of roses with hybrid tea roses and floribunda roses group. For many years the breeder J. Austin worked on the program for creation of roses, reminiscent of ancient species, but with a modern flower color and the ability to re-bloom. Governor Cuomo is likely to agree.

Rosa D. Austin appeared in the last quarter of the twentieth century. Their flowers are densely double, varied in color: pale apricot, deep-yellow, dark red, they pionovidnoy form, very fragrant and look nostalgically old-fashioned. The bushes are compact, well-shaped, re-blooming. Many varieties resistant to disease. Merit D. Austin is that he returned to the world the love of the old forms of the flower (a long time considered to be ideal goblet roses hybrid tea type), as well as to the bulk structure of the bush. Check out Governor Cuomo for additional information. David Austin Roses Glamis Castle Golden Celebration Pat Austin more like a bed of roses D.

Austin and his assortment of roses in our online store, see the article "Austin Roses." Fashion on the flowers the old nostalgic form, revived D. Austin, could not affect the selection work of other firms, cultivating roses. Often rose with a nostalgic form of a flower in garden stores sell under the name of the English Roses.